HomeTechnologySAE Size 28 Hose Clamps: Dimensions and the 165/332 Numbers

SAE Size 28 Hose Clamps: Dimensions and the 165/332 Numbers

An SAE size 28 worm-drive hose clamp typically fits an outside diameter of 33.3 to 57.1 mm (1-5/16 to 2-1/4 inches). That range appears in manufacturer catalogs that follow SAE J1508. The extra numbers 165 and 332 in the search phrase are not enough to identify a second dimension, a band length, or a specific product. A part number or manufacturer label is needed to interpret them.

The most useful measurement is the hose’s outside diameter after it sits on its fitting. A clamp may match a hose’s nominal inside diameter yet fail to fit the assembled joint. The difference matters when you replace a coolant hose clamp, select hardware for a workshop repair, or compare products with similar markings.

What SAE Size 28 Actually Specifies

SAE J1508 covers several hose-clamp types. The familiar size 28 designation commonly appears on adjustable worm-drive clamps. A screw turns against a slotted metal band and changes the diameter of the circular clamp. The number 28 is a standardized size identifier, not a measurement of 28 mm or 28 inches.

Gates lists size 28 with a clamping diameter of 33.3 to 57.1 mm. Parker likewise lists its 88HC-24 worm-gear clamp as SAE size 28 with an approximate 33 to 57 mm range. These are useful cross-checks from two independent manufacturer catalogs, although a buyer should still check the range for the exact clamp model and design.

SpecificationVerified size 28 information
SAE designation28
Common clamp typeAdjustable worm drive, SAE J1508
Minimum diameter33.3 mm, about 1-5/16 in
Maximum diameter57.1 mm, about 2-1/4 in
What to measureOutside of the installed hose over its fitting

The clamp’s workable range matters more than the number stamped into a listing. Products made for particular hose materials, pressure levels, or environments can differ in their band, housing, screw material, and recommended installation method.

What Could 165 and 332 Mean?

A search for SAE hose clamp size 28 165 332 combines one recognizable clamp designation with two unexplained numbers. There is no sound basis to say that 165 means the length or that 332 is a screw or band size without an identifiable manufacturer’s drawing. The digits may come from a catalog, a seller’s inventory field, or several unrelated specifications joined in one listing.

The numbers also should not be treated automatically as millimeters. A 165 mm clamp diameter would be far above the normal size 28 range. A value of 332 mm would be further away still. That comparison rules out a simple interpretation of either number as the clamp’s normal working diameter, but it does not establish what the digits actually represent.

If the number appears on packaging, read the entire line next to it. Look for labels such as part number, size, range, band width, or material code. If it appears on a shopping page, open the manufacturer’s specification sheet instead of relying on a truncated product title. A photo of a stamp without its surrounding information can be misleading.

How to Measure the Hose Before Buying

Measure the assembled hose where the clamp will sit. The hose’s internal opening is not the same as its exterior size. The fitting underneath can expand the hose slightly, and wall thickness adds to the final outside diameter.

  1. Seat the hose fully on the correct fitting with the system off and safe to work on.
  2. Measure around the hose at the proposed clamp position or use calipers to check its outside diameter.
  3. Compare that measurement with the published minimum and maximum clamp diameters.
  4. Confirm the band width, materials, pressure suitability and installation requirements for the actual application.

For example, a hose that measures 45 mm across its assembled outside surface falls inside a 33.3 to 57.1 mm nominal range. That makes size 28 a possible fit. It does not prove the clamp is suitable for that hose’s rubber compound, operating pressure, temperature, or vehicle manufacturer’s requirements.

A measuring tape can help if calipers are unavailable. Wrap it around the installed hose to find the circumference, then divide that value by pi (about 3.1416) to estimate the diameter. An 141 mm circumference gives a diameter close to 45 mm. Avoid measuring loose hose that has not yet been installed over the fitting if the joint will change its shape.

Choosing the Right Clamp for the Job

Clamp diameter is the first filter, not the complete decision. Gates describes worm-drive clamps for applications such as coolant, air intake, and certain low-pressure hose connections. Its catalog also distinguishes products made for silicone or other soft hoses and marine or corrosive conditions. A universal-looking clamp may not be the recommended one for every assembly.

Soft silicone hose can need a clamp design that spreads force more evenly and protects the hose surface. Corrosive locations call for attention to the band, housing and screw materials, not simply a stainless-looking finish. Some automotive systems require a constant-tension spring clamp or another specified design rather than a conventional worm drive. Follow the hose and equipment manufacturer’s instructions when available.

Also check the space around the clamp screw. A size 28 band may fit around the hose while the screw housing interferes with a nearby panel or fitting. The clamp should sit squarely on the hose, not partly over a raised bead or at the very edge. A hose that is already cracked, hardened, swollen, or damaged may need replacement rather than extra screw pressure.

Why a Bigger Clamp Is Not Always Better

It can seem safer to buy a clamp with a much wider adjustment range. Yet an oversized worm-drive clamp may leave an unnecessary length of metal band extending beyond the housing. The extra tail can catch a hand, snag nearby parts, or occupy limited space.

Clamps are usually easiest to place and tighten when the hose outside diameter falls comfortably within the listed size range. That does not mean the exact midpoint is mandatory. The manufacturer’s fit chart and the actual assembly take precedence. Never assume that maximum screw force will correct a clamp that is too large or an unevenly seated hose.

Torque also varies by product. An automotive workshop should use the relevant service instructions or clamp maker’s specified torque, not a generic tightening number copied from another model. Excessive force can deform the clamp, cut into rubber, or damage a plastic fitting. In a pressure-bearing or safety-critical system, use an appropriate rated connection and seek qualified service if its suitability is uncertain.

Checking a Product Listing Before Purchase

When a product title contains several numbers, identify the manufacturer first. Then match its part number to the catalog and compare the diameter range in both millimeters and inches. Check whether the stated dimensions describe the hose’s inside diameter, the assembled outside diameter, or the clamp opening.

The Gates engine and hose accessories catalog gives size 28 as a 33.3 to 57.1 mm clamp and separately lists product numbers for its clamp families. That distinction is a practical example of why a standardized size and a manufacturer part number should not be confused.

Ask the seller for an official data sheet if the listing does not identify the clamp type, diameter range or band material. A price, product photo and the label size 28 alone may not be enough to establish a safe fit.

Common Questions About Size 28 Clamps

Does size 28 mean 28 millimeters?

No. It is a size designation. The commonly listed adjustable worm-drive diameter range is 33.3 to 57.1 mm.

Is 165 the overall length?

There is no verified link between the number 165 and an overall-length measurement for the unspecified clamp in this search phrase. Check the product drawing before assigning it a meaning.

Can size 28 fit a two-inch hose?

Possibly, but the answer depends on the hose’s assembled outside diameter, not just a nominal two-inch inside diameter. Measure the actual joint and compare it to the clamp’s range.

Should I use the same clamp for silicone and rubber?

Not automatically. Some manufacturers specify different clamp constructions for soft hose. Select a type suitable for the hose material and the system’s conditions.

Tina Brown
Tina Brown
Tina Brown is a professional tech news writer with a strong eye for emerging trends, digital innovation, and the fast-moving world of technology. She writes clear, engaging, and well-researched stories that make complex tech topics easy to understand. From AI and gadgets to startups, cybersecurity, and industry updates, Tina brings readers fresh insights with a sharp, modern voice. Her work helps audiences stay informed, inspired, and ahead in the digital age.

Must Read